Saves the current routine.
command saves the current routine. You use ZLOAD
to load the routine, then use ZSAVE
to save any changes you have made to the routine with ZINSERT
is also used to name a routine loaded with an argumentless ZLOAD
, or a nameless routine created by ZINSERT
moves the edit pointer to the end of the routine. Issuing ZSAVE
moves the edit pointer even if no actual save was needed.
If you ZLOAD
a routine and then ZSAVE
it to the same routine name without making any changes to the routine, InterSystems IRIS does not update the routine’s timestamps or generated flag.
You can use ZSAVE
in two contexts: from the Terminal prompt, or invoked by an XECUTE
command within a program.
without an argument saves the current routine under its current name (that is, the name under which you previously saved it) on disk in the current namespace. If the current routine does not yet have a name, an argumentless ZSAVE
generates a <COMMAND> error.
saves the current routine to disk as the specified routine
name in the current namespace.
If use the XECUTE
command to invoke ZSAVE routine
, the system creates a Load frame to preserve the current routine. When the XECUTE
command concludes, InterSystems IRIS uses this Load frame to restore the routine name prior to the XECUTE
as the current routine. This is shown in the following example:
WRITE "Current routine name",!
WRITE "initial name: ",$ZNAME,!
SET x = "WRITE $ZNAME"
SET y = "ZSAVE mytest"
SET z = "WRITE "" changed to "",$ZNAME,!"
WRITE "restored name: ",$ZNAME,!
An optional postconditional expression. InterSystems IRIS executes the command if the postconditional expression is true (evaluates to a nonzero numeric value). InterSystems IRIS does not execute the command if the postconditional expression is false (evaluates to zero). For further details, refer to Command Postconditional Expressions
in Using ObjectScript
A name under which to save the routine. routine
must be a valid routine name. You can use the $ZNAME("string",1)
function to determine if string
is a valid routine name. You can use the $ZNAME
special variable to determine the name of the currently loaded routine.
is a new name for the routine, but it can be the current routine name. If a routine by that name already exists, InterSystems IRIS overwrites it. Note that you are not asked to confirm the overwrite. A routine name must be unique within the first 255 characters; routine names longer than 220 characters should be avoided.
If you specify ZSAVE routine
in an X
If you omit routine
, the system saves the routine under its current name. If no current name exists, ZSAVE
generates a <COMMAND> error.
The following Terminal session example executes a ZSAVE
command to save the currently loaded routine:
this is line 8
this is line 9
WRITE "this is line 8",!
WRITE "this is line 9",!
this is line 9
command works only when entered in the Terminal or when coded within an XECUTE
statement in a routine. It should not be coded into the body of a routine because its operation would effect the execution of that routine. If you code ZSAVE
in a routine, but outside of an XECUTE
statement, that ZSAVE
saves the current program.
and Routine Recompilation
If you have issued a command that modifies source code, ZSAVE
recompiles and saves the routine. If the source code for the routine is unavailable, ZSAVE
fails with a <NO SOURCE> error and does not replace the existing object code. For example, the following commands load the %SS object code routine, attempt to remove lines from the (nonexistent) source code, and then attempt to save to the ^text global. This operation fails with a <NO SOURCE> error:
ZLOAD %SS ZREMOVE +3 ZSAVE ^test
If you have not
issued a command that modifies source code, ZSAVE
saves the object code in the specified routine
. (Obviously, no recompile occurs.) For example, the following commands load the %SS object code routine and then save it to the ^text global. This operation succeeds:
You receive a <PROTECT> error if you try to ZSAVE
a %routine to a remote dataset, even if that dataset is the current dataset for the process. The percent sign prefix is used for the names of non-modifiable routines, such as system utilities.
Concurrent ZSAVE Operations
When using ZSAVE
in a networked environment, a situation may occur in which two different jobs might concurrently save a routine and assign it the same name. This operation has the potential for one routine overwriting part of the other, producing unpredictable results. When this possibility exists, acquire an advisory lock on the routine before the ZSAVE
operation. For example, LOCK ^ROUTINE("name")
. For further details, refer to the LOCK
command. When running a job across ECP, the saved source is more vulnerable to such concurrent saves because local buffer protection is not visible to other clients.
Content Date/Time: 2019-02-18 01:15:52